Код ошибки
|
Описание
|
01-01
|
Frequency monitoring and zero cross problem
|
01-02
|
Interlock
|
01-03
|
AC power problem
|
01-04
|
Finisher interlock
|
01-05
|
24v problem
|
03-01
|
Optics to main board communication problem
|
03-02
|
Software reset problem
|
03-03
|
Could be punched holes in the lead edge of the original
|
03-04
|
Software problem
|
03-06
|
Low battery
|
03-07
|
NVM not initialized or is missing or defective
|
03-17
|
Communication problem between main board and finisher board
|
03-18
|
Initializes one NVM counter to agree to others
|
03-19
|
All three NVM counter to agree with others
|
03-20
|
Main board/interface board problems
|
03-21
|
Problem with RIC NVM
|
03-22
|
RIC modem problem
|
03-23
|
RIC real time clock failure.
|
03-25
|
RIC NVM problem or not initialized
|
03-27
|
NVM problem
|
03-28
|
Watchdog software problem
|
03-29
|
Microprocessor crystal not at correct frequency
|
03-30
|
No software response from finisher after 20 seconds have elapsed
|
06-01
|
Lens did not reach 1.1 position
|
06-02
|
1/2 rate scanner problem
|
06-03
|
Scan home problem
|
06-04
|
Scan home problem
|
06-05
|
Scan home problem
|
06-06
|
Scan encoder
|
06-07
|
Scan encoder
|
06-08
|
Scan drive boost
|
06-09
|
Scan encoder
|
06-11
|
Scan encoder pulse phases
|
06-12
|
Insufficient scan damping
|
07-01
|
Duplex tray not home during duplexing
|
07-02
|
Tray 2 not home when selected
|
07-13
|
Tray 2 height sensor problem
|
07-15
|
Tray 2 empty
|
07-16
|
Tray 1 door open
|
07-18
|
Tray 1 stack sensor
|
07-22
|
Tray 1 empty
|
07-26
|
Tray 1 bypass switch actuated too long
|
07-27
|
Tray 1 bypass switch deactuated too early
|
07-30
|
Paper in duplex
|
07-31
|
Paper in duplex
|
07-32
|
Duplex tray empty, when paper should be there
|
08-10
|
Paper did not reach tray 2 input tray sensor
|
08-11
|
Paper did not reach duplex input sensor
|
08-12
|
Paper did not reach tray 1
|
08-14
|
Paper did not leave tray 2 input sensor quickly enough
|
08-18
|
Trail edge did not reach tray 2 input sensor quickly enough
|
08-19
|
Trail edge did not reach tray 1 input sensor quickly enough
|
08-20
|
Paper in duplex
|
08-21
|
Paper in tray 2 input
|
08-22
|
Paper in tray 2 or duplex at wrong time
|
08-23
|
Paper at tray 1 input at wrong time
|
08-24
|
Paper in tray 1 at wrong time
|
08-28
|
Upper and lower nips problem
|
09-08
|
Low toner condition
|
09-12
|
Drum signals are out of range
|
09-13
|
Unstable drum patch readings
|
09-15
|
Patch is too dark
|
09-16
|
Patch is too light
|
09-17
|
Open toner container access cover
|
09-18
|
Low toner level
|
09-21
|
Low toner sensor disconnected
|
09-22
|
Low toner condition, even after machine has been theoretically, adding toner
|
10-02
|
Low fuser temperature
|
10-03
|
High fuser temperature
|
10-06
|
Paper did not reach out put switch
|
10-07
|
Paper stayed on output switch
|
10-10
|
Paper did not reach decurler sensor
|
10-11
|
Paper did not reach decurler sensor
|
10-12
|
Paper on decurler sensor
|
10-13
|
Paper did not reach duplex entry sensor in time
|
10-14
|
Paper did not reach duplex entry sensor in time
|
10-15
|
Paper on entry sensor at wrong time
|
10-17
|
Fuser temperature is too high and fuser relay has deactuated
|
12-01
|
Paper at finisher input sensor
|
12-02
|
Paper did not reach finisher
|
12-03
|
Paper reached finisher too soon
|
12-05
|
Paper at stapler
|
12-06
|
Paper at stapler
|
12-07
|
Paper did not reach stapler
|
12-08
|
Paper did not reach stapler
|
12-10
|
Complied motor not working properly
|
12-15
|
Eject motor problem and/or eject encoder
|
12-20
|
Stacker motor problem
|
12-21
|
Stacker interlock
|
12-22
|
Stacker bottom sensor
|
12-23
|
Stacker bottom sensor
|
12-24
|
Stacker bottom sensor senses full
|
12-25
|
Stack height sensor
|
12-26
|
Stack height sensor
|
12-27
|
Stack height sensor
|
12-30
|
Offset home sensor
|
12-31
|
Offset home sensor
|
12-32
|
OCT switch
|
12-35
|
Eject nip carriage
|
12-36
|
Eject cam interlock
|
12-37
|
Eject nip carriage open timing
|
12-38
|
Eject cam interlock
|
12-40
|
Tamper motor
|
12-41
|
Tamper home problem
|
12-42
|
Tamper home sensor
|
12-43
|
Staple load sensor
|
12-44
|
Tamper home sensor
|
12-45
|
Tamper home sensor
|
12-50
|
Low on staples
|
12-51
|
Stapler home sensor
|
12-52
|
Stapler home sensor
|
12-53
|
Eject cam interlock
|
33-37
|
Too few documents
|
55-01
|
RDH interlock switch open during use
|
55-04
|
Paper on bypass sensor
|
55-05
|
Paper at vacuum timing sensor
|
55-06
|
Paper on output sensor
|
55-10
|
No paper reached S31
|
55-20
|
Paper did not leave S31 at correct time
|
55-24
|
Set counter arm problem
|
55-25
|
Documents in input tray not detected
|
55-27
|
Lead edge did not reach S35 at correct time
|
55-2955-30
|
Trail edge did not reach S35 at correct time
|
55-31
|
S32, ADF registration sensor did not see paper at correct time
|
55-32
|
S32 did not see trail edge at correct time
|
55-33
|
S36 One too many documents
|
55-36
|
One too many documents
|
55-39
|
Hole count problem on document feeder belt
|
55-40
|
Document belt travel problem
|
55-41
|
Document belt mistracking or skewing
|
55-45
|
Paper at inverter sensor
|
55-47
|
Inverter sensor did not see paper lead edge at correct time
|
55-49
|
More than 50 sheets in input tray
|
55-50
|
Right side interlock
|
55-51
|
Left side interlock
|
55-55
|
Document on glass
|
93-93
|
NVM has to be initialized after new software installed
|