Код ошибки
|
Описание
|
CC-nn
|
Original sensing problem
|
CH
|
Lit steadily: Door open
|
CH
|
Flashing: Developer unit not installed, not latched or not installed properly
|
EE-EL
|
During developer calibration, overtoned condition detected
|
EE-EU
|
During developer calibration, undertoned condition detected
|
F1-00
|
Communication problem between main board and stapler
|
F1-02
|
Stapler sorter transport drive problem
|
F1-03
|
Problem with guide bar oscillator motor
|
F1-04
|
Index lower sensor
|
F1-05
|
Index upper sensor
|
F1-06
|
Shift motor problem in stapler sorter, or index motor problem
|
F1-08
|
Staple sorter shift motor drive problem
|
F1-10
|
Stapler problem
|
F2-00
|
Toner sensor problem
|
F2-31
|
Drum surface reflecting problem
|
F2-32
|
Drum sensor not scanning mark properly
|
F2-33
|
Grid voltage is too high or too low
|
F2-35
|
During patch detection, measurement is wrong
|
F2-37
|
Drum mark sensor adjustment problem
|
F3-01
|
LCT encoder
|
F3-02
|
LCT lift problem
|
F3-03
|
LCT down problem
|
F3-12
|
Cassette 1 lift problem
|
F3-22
|
Cassette 2 lift problem
|
F3-32
|
Cassette 3 lift problem
|
F3-42
|
Cassette 4 lift problem
|
H2-00
|
Fuser thermistor
|
H3-00
|
Fuser temperature too high
|
H4-00
|
Fuser temperature too low
|
L1-00
|
Scan problem
|
L2-00
|
Mirror motor drive problem
|
L3-00
|
Scan return problem
|
L4-01
|
Drum motor drive problem
|
L4-02
|
Main motor drive problem
|
L5-00
|
4/5 mirror drive problem
|
L8-01
|
Full wave signal missing to auto exposure
|
L8-02
|
Full wave signal to auto exposure is incorrect
|
L8-03
|
During auto exposure adjust procedure, the auto exp.
|
P20
|
Adjust automatic exposure
|
P21
|
Auto shut off timing
|
P22
|
Toner save mode
|
P25
|
Maximum number of copies that can be selected
|
P26
|
Margin shift
|
P28
|
Initial status
|
P29
|
To read total copies
|
P70
|
Auto paper select
|
P72
|
Bypass in duplex
|
P74
|
Stop document feeder use
|
P75
|
Stop duplex use
|
P76
|
Stop stapler use
|
P83
|
Modem access to codes through phone line
|
P90
|
Display all of the operator programs
|
PC
|
Card counter
|
PF
|
Modem problem
|
U0-00
|
Operation panel problem
|
U2-00
|
EEPROM error. Reset with sim. 16
|
U3-00
|
Communication problem between master and mirror controller
|
U3-20
|
Mirror drive problem
|
U3-21
|
Mirror home sensor problem
|
U3-26
|
Mirror motor voltage problem
|
U3-41
|
Lens motor home correction did not go well
|
U3-42
|
4/5 mirror motor problem similar to U3 -41
|
U4-02
|
Duplex alignment plate sensor
|
U4-03
|
Duplex rear plate sensor
|
U5-00
|
Communication problem between RADF and copier
|
U5-01
|
RADF resist sensor
|
U5-02
|
RADF reverse sensor
|
U5-03
|
RADF timing sensor
|
U5-04
|
RADF empty sensor
|
U5-11
|
RADF paper feed drive problem
|
U5-12
|
RADF transport drive problem
|
U7-00
|
Communication problem between copier and modem
|
