Код ошибки
|
Описание
|
101
|
Exposure lamp
|
103
|
Power frequency problem
|
104
|
Exposure lamp
|
120
|
Scanner home problem
|
121
|
Scan home problem
|
125
|
Scanning too slow
|
126
|
Scanning too fast
|
127
|
Scan drive problem or encoder
|
140
|
Lens home problem (vertical)
|
141
|
Lens home problem (vertical)
|
142
|
Lens home problem (horizontal)
|
143
|
Lens home problem (horizontal)
|
144
|
3rd scan sensor problem
|
145
|
3rd scan sensor problem
|
146
|
Magnification problem
|
190
|
Optics thermistor open circuit
|
191
|
Scan motor thermistor
|
302
|
Charge corona short
|
303
|
Charge corona cleaner problem
|
341
|
Developer motor drive problem
|
342
|
Toner disposal motor drive problem
|
343
|
Vsp. Problem. Image density sensor problem
|
351
|
Vsg. Problem. Higher than 4. 3 volts. Image density sensor problem
|
352
|
Toner sensor problem during developer calibration
|
353
|
Vsp Problem. Image density sensor, drum bias or HVT
|
354
|
Vsg Problem. Image density sensor, drum bias or HVT
|
355
|
Toner density sensor problem. Vtd problem. Undertoned
|
356
|
Toner density sensor problem. Vtd problem. Overtoned
|
357
|
Vsp problem. Image density sensor, drum
|
358
|
Vsp problem. Image density sensor, drum, toner dust
|
361
|
Drum potential sensor calibration during process control setup
|
364
|
Vd problem. Drum potential sensor, drum or charge corona
|
365
|
V1 problem. Drum potential sensor, drum, charge corona, dirty optics
|
402
|
Transfer, transfer belt, HVT
|
440
|
Main motor speed problem
|
442
|
Drum thermistor
|
500
|
Bypass feed
|
501
|
Paper feed motor
|
502
|
1st lift motor
|
503
|
2nd lift motor
|
504
|
3rd lift motor
|
506
|
LCT motor
|
507
|
LCT feed motor
|
508
|
Tandem fence motor
|
510
|
Tandem side home sensor
|
511
|
Tandem side home sensor
|
520
|
Duplex/fuser drive motor problem
|
522
|
Jogger home sensor
|
523
|
Jogger home sensor
|
541
|
Fuser thermistor
|
542
|
Fuser does not warm-up
|
543
|
Fuser temperature too high. Monitored by main board
|
544
|
Fuser temperature too high. Monitored by optics board
|
545
|
Low fuser temperature. Monitored by main board
|
546
|
Low fuser temperature. Monitored by optics board
|
547
|
Fuser lamp won't shut off
|
548
|
Erratic fuser temperature
|
600
|
Communication problem between main board and operation board
|
601
|
Communication problem between main board and optics board
|
602
|
Communication problem between main board and high voltage unit
|
603
|
Main board problem
|
620
|
Communication problem between main board and document feeder boards
|
621
|
Communication problem between main board and sorter staplers or finisher
|
700
|
DJF/RDH feed motor
|
701
|
DJF/RDH transport belt problem
|
702
|
DJF exit or RDH inverter motor
|
703
|
RDH exit motor problem
|
730
|
Sorter/stapler or finisher transport motor
|
731
|
Bin lift motor
|
732
|
Tray shift motor
|
733
|
Tray shift lift motor
|
735
|
Duplex jogger motor
|
737
|
Gripper motor
|
738
|
Staple motor
|
740
|
Staple drive motor
|
741
|
Bin rear plate motor (stapler)
|
742
|
Finisher stack feed motor
|
900
|
Total counter
|
901
|
Total counter
|
SC
|
Full waste toner bottle. Technician must empty this. Emptying the waste toner and reinstalling the bottle will clear this code
|
