Код ошибки
|
Описание
|
E000
|
After power-on, the upper fixing roller does not reach 100 C within 5 min
|
E001
|
The temperature of the upper fixing roller exceeds 230 C for 5 sec or more
|
E002
|
After the temperature of the upper fixing roller has exceeded 100 C, it does not reach 180 C within 5 min
|
E003
|
After the temperature of the upper fixing roller has reached 180 C, it drops to 100 C or less for 5 sec or more
|
E005
|
The length used of the cleaning belt inside the fixing assembly has exceeded a specific value
|
E012
|
After the drum motor drive signal has been generated, clock pulses are not generated within 2 sec
|
E013
|
After the waste toner feeding screw has become locked, the detecting switch (SW20) is pressed a multiple number of times within a specific period of time
|
E014
|
When the fixing motor (M17) is rotating, an error is detected for 2 sec or more
|
E015
|
After the pick up motor drive signal has been generated, clock pulses have not been generated within 2 sec
|
E019
|
As many as 50,000 have been made after detecting a waste toner full condition
|
E020
|
During copying, the toner supply signal is 0', indicating the absence of toner, for 3 min or more. During toner supply sequence at time of installation, the toner supply signal does not go '1' after 6 min or more
|
E030
|
After the total copy counter has turned OFF, an open circuit is detected for the total copy counter
|
E032
|
After the clock pulse signal reached the IPC communication format of the copier DC controller PCB, the Copy Data Controller-A1 does not detect the signal
|
E050
|
While the paper jogging guide motor (M11) drive signal is being generated, the paper guide home position signal (THP) is not generated for 2 sec or more. While the paper jogging guide motor (M11) is being generated, the paper jogging guide home position signal (THP) is generated for two sec or more
|
E202
|
The scanner home position signal (SCHP) is not generated within 10 sec after the power switch or the Copy Start Key is pressed
|
E203
|
While the scanner motor drive signal is being generated, clock pulses are not generated within 2 sec
|
E204
|
The scanner leading edge signal (SCDP1) is not generated within 0.8 sec after the scanner has started to move
|
E209
|
The scanner C.F.F. position signal (SCFFP) is not generated within 10 sec after the C.F.F. has been sent
|
E210
|
The lens X home position signal (SCFFP) is not generated within 10 sec after the C.F.F. has been sent
|
E212
|
The lens Y home position signal (LYHP) is not generated within 9 sec after the power switch or the Copy Start Key is turned ON. The lens Y home position signal (LYHP) is generated for 2 sec or more
|
E213
|
In stream reading mode, the scanner original leading edge sensor 2 signal (SCDP2) is not generated for 5 pages continuously
|
E214
|
While the scanner cooling fan (FM1, FM10, FM11) is rotating, an error signal is generated for 2 sec or more
|
E270
|
In stream reading mode, the scanner leading edge signal(SCDP2) is not generated within a specific period of time after a command has been issued to lock the scanner
|
E710
|
At power-on the IPC (Q170) on the DC controller PCB cannot be initialized
|
E711
|
After power-on the IPC (Q170) on the DC controller PCB goes out of order
|
E712
|
The communication IC on the RDF controller PCB has gone out of order
|
E713
|
The communication IC on the sorter control PCB has gone out of order
|
E715
|
The communication IC on the C.F.F. controller PCB has gone out of order
|
E717
|
The communication IC on the Copy Data Controller-A1 PCB has gone out of order
|
E800
|
An open circuit is detected
|
E801
|
Current flows from the activation circuit in the absence of the scanning lamp ON signal
|
E802
|
The relay (RL3) in the power supply unit does not operate in spite of the auto power-off signal
|
